Back to Overview

Why Your Light Steel Villa Feels Unbearably Hot (And Why Adding More Insulation Won’t Solve It)

Nov 19,2026

Why Your Light Steel Villa Feels Hot (And Why More Insulation Won't Fix It)

A buyer moves in, runs the air conditioning for a month, and sends the electricity bill with a question attached. The house has 100 mm of glass wool in every wall. The brochure said it was equivalent to a metre of brick. So why does the second floor stay warm until midnight?

The insulation is not lying and it is not the problem. The problem is that a wall's performance is decided by four things — conduction, thermal bridging, air leakage and solar gain — and insulation only addresses the first. Buyers pay for the first and then live with the other three.

The number on the brochure is not the number in the wall

Insulation is rated by conductivity, and the useful conversion is simple: resistance equals thickness divided by conductivity. A hundred millimetres of glass wool at 0.038 W/m·K gives you about 2.6 m²K/W.

A metre of solid brick, at roughly 0.7 W/m·K, gives you about 1.4.

So the comparison in the catalogue is real, and conservative. The mistake is assuming that the wall's performance equals the insulation's performance. It does not. The wall is a chain of layers, and it performs like its weakest link — plus whatever the frame does to shortcut it.

The studs are short-circuiting the wall

Steel conducts heat roughly a thousand times better than mineral wool. At 400 to 600 mm centres, the studs occupy ten to twenty percent of the wall area and conduct straight through the cavity, from the cold side to the warm side.

This is thermal bridging, and in a light steel wall it is not a detail. Depending on framing ratio and detailing, it can remove a fifth to a third of the benefit the cavity insulation was supposed to deliver. The wool does its job; the heat simply goes around it.

Which is why the layer outside the sheathing matters more than buyers expect. In our wall build, 30 mm of XPS sits outside the OSB, continuous, unbroken by the frame. That is not decoration and it is not there for waterproofing. It is the only layer in the assembly that has no steel passing through it, and it is what stops the studs from short-circuiting the whole wall.

Remove it to save a few percent, and the wall keeps its R-value on paper and loses it in practice.

The roof is doing most of the damage

In a hot climate, the wall is usually not the biggest problem. The roof is.

A dark metal roof surface can reach 70 °C or more in direct sun. That heat arrives at the ceiling by three routes: conduction through the roof build-up, radiation across the cavity, and hot air that has been sitting in an unventilated void.

Three things fix it, in order of value:

A ventilated cavity above the insulation. Air enters at the eaves and leaves at the ridge, carrying heat away before it reaches the ceiling. Without ventilation, the cavity becomes an oven.

A radiant barrier facing an air gap. Low-emissivity foil works by reflecting radiation, and it only works if there is an air space in front of it. Foil laminated directly to a board does very little.

Insulation at ceiling level, not under the tiles. Insulating the ceiling plane keeps the hot roof deck outside the thermal envelope, where it belongs.

On a two-storey house, the upper floor sits closest to this problem and gets the least benefit from wall insulation. That is usually the room the complaint comes from.

Air leaks, not just heat

A vapour barrier is specified for moisture. It is also, if it is sealed properly, the air barrier — and air leaking out of a house takes your cooled air with it and brings humidity in.

The leakage is rarely dramatic. It is a five-millimetre gap at a sole plate, a service penetration sealed with nothing, a junction where the membrane stops short of the frame. Around the perimeter of a house, those small gaps add up to the equivalent of leaving a window open a crack, permanently.

The same joints that fail a blower-door test are the ones that let humid air condense inside the wall. Airtightness is not an efficiency upgrade. It is the same detail doing two jobs.

Windows and shading beat U-values

In tropical and subtropical markets, the heat coming through glass is mostly radiant, and the number that governs it is solar heat gain, not the U-value the sales sheet emphasises.

A single-glazed unit with a low U-value is still a window that lets sunlight in. What actually helps:

Low-e coating with a low solar heat gain coefficient

External shading — overhangs, fins, louvres — designed for the sun angle at your latitude

Orientation decisions made at the drawing stage, when they are free

Thermal breaks in the frame, so the frame does not become the wall's weak point

A house with modest insulation and good shading will outperform a well-insulated house with unshaded west glazing. That is not an opinion, it is the order of magnitude.

What to write into the specification

U-value for the wall and roof assemblies, as built, not as insulated

Continuous insulation outside the stud line, with thickness and material

Framing ratio, and whether thermal breaks or staggered studs are used

Roof: ventilated cavity depth, inlet and outlet area, radiant barrier with air gap

Airtightness target, and the taping detail at sole plates and penetrations

Glazing: solar heat gain coefficient, low-e type, frame thermal break

External shading, drawn on the elevations

A supplier who can only quote "100 mm glass wool" is answering one of seven questions.

The honest version

Insulation is the easiest thing to sell and one of the smaller levers. The three that matter more — continuous insulation outside the frame, a ventilated roof, and airtight detailing — are invisible after handover, which is precisely why they get value-engineered out.

If your house runs hot, the first question is not how much wool is in the wall. It is whether the roof is ventilated, whether the studs have a continuous layer outside them, and whether the west windows have anything in front of them.

Fix those, and the 100 mm starts performing the way the brochure promised.

FAQ

How much insulation does a light steel villa need?

For a hot climate, 100 mm of mineral wool in the wall cavity plus 30 mm of continuous insulation outside the studs is a sensible baseline. For cold climates the cavity depth increases and the continuous layer becomes more important, not less.

Is 100 mm of glass wool really equal to a metre of brick?

In pure resistance terms, roughly yes — 100 mm at 0.038 W/m·K gives about 2.6 m²K/W, against about 1.4 for a metre of solid brick. The comparison is fair for the insulation alone, but a wall assembly also loses performance at the frame and the joints.

Does the steel frame cause thermal bridging?

Yes, significantly. Steel conducts heat far better than insulation, and studs at 400 to 600 mm centres can remove a fifth to a third of the cavity's benefit. A continuous insulation layer outside the sheathing is the standard remedy.

What matters more, wall insulation or roof insulation?

In hot climates, the roof. It receives the most solar radiation and sits directly above the rooms people complain about. A ventilated cavity and a radiant barrier with an air gap often deliver more comfort per dollar than extra wall thickness.

Will better insulation reduce my air conditioning bill?

It helps, but airtightness and shading usually matter more. A leaky, unshaded, well-insulated house still runs its air conditioner hard, because the heat is arriving through the glass and the gaps rather than through the wall.

PREVIOUS: